化工领域中对流传热系数α的计算

对流传热是热传递的三种基本方式之一,化学工程中的对流传热并非单纯对流而是流体流过固体表面时发生的对流和传导联合作用的传热过程。描述对流传热速率的方程式形式简单,所有问题集中在对流传热系数α中。因此对流传热系数α的计算是对流传热过程的关键。     

Analysis of the stratified / nonstratified transitional boundary in horizontal and slightly inclined condensing flows

A mechanistic model has been developed for determining the stratified boundary for condensing flows in horizontal and slightly inclined tubes. Two formulations, a complete and a simplified version are considered for the equilibrium liquid level. Good agreement is found between the two formulations and generalized results were derived from the simplified version of the model. From these results, the effect of condensation is shown to be equivalent to adding a small upward inclination in adiabatic gas-liquid flow. The predicted transition line is compared with flow-regime data of different fluid properties, tube diameters, and inclinations. The predictions agreed reasonably well with the data.     

三代微光管均匀性测试与分析

利用自行研制的“光电阴极多信息量测试系统”首次对国产三代微光管中的GaAs光电阴极的均匀性进行了光谱响应测试 ,结果表明该国产三代微光管存在明显的非均匀性。利用曲线拟合方法估算了GaAs光电阴极的材料性能参数 ,发现表面逸出概率不一致是非均匀性的主要原因 ,GaAs材料的少子扩散长度 (1 1 2～ 1 82 ) μm ,与阴极厚度相当 ,后界面复合速率在 (1× 1 0 5～ 1× 1 0 6 )cm/s之间 ,它限制了阴极灵敏度的提高     

彩色显象管曝光台校准仪光学系统的设计

论述了彩色显象管曝光台校准仪的基本原理和光学系统的设计方法，分析了系统测量精度及有关性能参数。     

Deflections of highly inflated fabric tubes

Inflatable beams made of modern textile materials with important mechanical characteristics can be inflated at high pressure. The aim of the paper is to present experimental, analytical and numerical results on the deflections of highly inflated fabric tubes submitted to bending loads. Experiments are displayed and we show that tube behaviour looks like that of inflatable panels (Thin-Walled Struct. 40 (2002) 523–536). Equilibrium equations are once again written in the deformed state to take into account the geometrical stiffness and the following forces. The influence of the shear stress cannot be neglected and Timoshenko’s beam theory is used. A new inflatable tube theory is established and simple analytical formulas are given for a cantilever-inflated tube. Comparisons between analytical and experimental results are shown. A new inflatable finite tube element is constructed by use of algebraic operations, because the compliance matrix of the cantilever beam is not symmetric. Comparisons between experimental, analytical and numerical results prove the accuracy of this beam theory and on this new finite element for solving problems on the deflections of highly inflated tubes.     

扁管承压能力的有限元分析

应用有限元分析方法，对相同周长、相同壁厚的扁管在直边段和圆弧半径的不同比值条件下与所能承受最大外压力的关系进行了分析．并对计算分析取得的数据进行拟和得到了扁管在直边段和圆弧半径的不同比值条件下能承受最大外压力的关系及经验公式．     

焊接箱型截面构件在不同焊缝熔深下承载力性能试验研究

为了有效改善大跨度桥梁中管翼缘焊接箱型截面构件的耐久性的问题,提出采用耐候钢代替普通钢的管翼缘箱型截面梁。同时,为了研究耐候钢管翼缘焊接箱型截面构件填充混凝土后在全熔透和部分熔透条件下的单轴承载力性能,开展了焊接矩形截面在三种不同焊缝熔深下的耐候钢管混凝土截面轴压短柱试验研究。分别测试每个试件在单轴压力作用下的静态应变、动态应变,以及竖向位移和侧向位移。对比构件承载力的试验结果及理论分析结果,得出不同熔深下焊接箱型截面管翼缘组合构件的承载力性能。研究结果表明:1）耐候钢管翼缘焊接箱型截面构件的全熔透焊缝承载力高于部分熔透焊缝承载力。2）全熔透试件开裂时的竖向位移较部分熔透试件的位移值大,而不同熔深下构件的横向位移测点L4随轴压荷载的增大而有增加,L3测点横向位移规律不明显。3）不同耐候钢管翼缘焊接箱型截面构件横向整体受拉,局部在顶部角部位置受压。构件的混凝土内部和钢板表面应变情况复杂,规律不明显。     

冷拔内螺纹管拉拔力的有限元计算方法

本文基于三维弹塑性大变形有限元分析理论,通过对内螺旋凸筋管冷拔成形过程进行有限元仿真,建立增量步与拉拔力的关系,提出了拉拔力的计算方法.经实验验证,理论计算值与实测值相吻合,可为拉拔模具和工艺参数的设计提供参考.     

缩进式管子-管板焊接工艺

管子-管板焊接是换热器生产的关键工序,通过对缩进式管子-管板焊接技术进行的试验和分析,确定了最佳的焊接参数,供换热器制造厂有关技术人员参考.